Celli is arguably the leading name in Australia in this class of farm machinery, best known for sales of rotary hoes, power harrows and mulchers.

Celli Farm Machinery

MIZAR/F Mulcher


The Heavy-Duty Low-Body Prunings and Grass Mulcher is suitable for Orchard, Vineyard and Grass cutting applications.

Celli MIZAR/F Heavy-Duty Low Body Prunings and Grass Mulcher

Photograph for illustration purposes - standard specifications may not match those shown.

FEATURES OF THE CELLI MIZAR/F MULCHER

3-POINT LINKAGE HITCH

MIZAR/F 3 point Linkage
  • Category 1 & 2 linkage headstock
  • 3 lower link pin positions accommodates various tractor sizes
  • Slotted top link clevis for floating operation
  • Head-stock can be mounted in two positions for Centre and 40cm Offset positions
  • 3-way headstock support with tie-rod
  • Retractable Parking stand

TRANSMISSION

  • 540 PTO rpm gearbox input
  • Gear box, driveline, body and rotor rated to 95 hp
  • Free wheel in gearbox so that on disengaging the PTO, the mulching rotor winds down without driving through the gear box and PTO drive shaft
  • The Rotor is driven by 4 belts (3 belts up to the 155 cm width model)
  • Heavy duty 168mm diameter rotor for strength

ROTOR

MIZAR/F Rotor
  • Rotor spins on self-aligning bearings with high radial load capacity ideal for the forces created by drive belts and the mulching operation.
  • The bearing is mounted within the rotor with labyrinth protection resisting the entry of debris for longer life.
  • Internal bearings gives a flat end plate for mulching up close to trees and obstacles.

MULCHING CHAMBER

MIZAR/F Mulching Chamber
  • The cut-away drawing shows the combination of hammers and counter blades working together to produce an excellent mulching environment
  • Hammers operate at over 2280 rpm for a high tip speed to produce a fine mulch of woody prunings or grass alike
  • Optional Rear rake tines retains prunings within the mulcher chamber to produce a finer mulch
  • Double counter blades resist the flow of larger material allowing hammers to produce a finer mulch
  • Rear rake tines retains prunings within the mulcher chamber to produce a finer mulch
MIZAR/F Twin plate construction
  • Twin plate construction produces 3 box-section areas in the body for superb body stiffness and strength and lower noise
  • To reduce body dents that initiate rust and accelerate deterioration, the twin plates also provide an inner skin to take the hard impacts reducing outer skin dents.
MIZAR/F Hammer
  • The hammer is forged and heat treated from high-grade steel and hardened
  • The hanging bolt is embedded into the hanging point for protection and to prevent spinning and unnecessary wear
  • The use of genuine Celli blades, hammers and bolts are essential for safety, performance and protection of the mulcher
MIZAR/F Rear roller
  • The slotted rear box section shows where the pruning rake tines are inserted
  • The body end plates are protected by a heavy duty skid
  • Skids provide primary protection of the body end plates and are not intended to be the means of height control
  • A rear roller (or optional wheels) are the best method of cutting height control

ROLLER

MIZAR/F Roller
  • A large 194mm diameter rear roller with scraper provides mulcher height control
  • The Roller's bearings are protected against grit and debris by a double-Z labyrinth for longer bearing life
  • Bearings for rear rollers need good protection for long life
  • The bearings are mounted on the inside of the skids to also reduce damage from collisions
MIZAR/F Rear

APPLICATIONS

  • Vineyards interrow grass cutting and mulching of prunings
  • General grass cutting and topping
  • Prunings up to 45mm
Application of MIZAR/F
  • Vineyards interrow grass cutting and mulching of prunings
  • Orchards (Fruit and Nut)
  • General grass cutting and topping
  • Road side maintenance
  • Prunings up to 70mm

OPTIONS

  • Rear semi-swivel wheel kits in lieu of roller
  • Side-mounted hydraulic disk mower
  • Front-mounted hydraulic sweeper
MIZAR/F Optional knives
  • Tri-Y Blades in lieu of Hammers

SPECIFICATIONS

MIZAR/F 150
MIZAR/F 175
MIZAR/F 200
MIZAR/F 225
MIZAR/F 250
Working Width (m)
1.50
1.75
2.00
2.25
2.50
Overall Width (m)
1.68
1.93
2.18
2.43
2.68
No. of Hammers
14
16
18
20
22
Weight (kg)
500
550
600
650
700
Tractor Power (hp)
45-80
50-90
55-90
60-90
70-90

BROCHURE

Click this link to download a brochure. Please note that Australian specifications may vary to those shown on the manufacturer's brochure and website. Follow this link to the manufacturer's website (Celli)

Disclaimer: Specifications and features described on the website are subject to change without notice. All care has been taken to present accurate information, however, the company is not liable for unintended errors or omissions.